Photo Source: chairtalks.com
If you have an office chair with a five-prong base, you may be wondering how to remove it. The process is actually quite simple and only takes a few minutes. With a little bit of know-how, you’ll be able to remove your office chair base with ease! In fact, with a few simple steps, you can have the task completed in no time at all. Let’s take a look at how it’s done.
What You Will Need
Photo Source: btod.com
There are things that you need to prepare before you remove your office chair base. Here is the list of materials that you’ll need:
- Phillips head screwdriver. This is the most important tool that you will need in order to remove your office chair base. Also, make sure that the screwdriver is small enough to fit in the screw holes.
- Hammer. You will need a hammer in order to remove the plastic plugs that are holding the base in place. It’s best to use a wooden handle so that you don’t damage the upholstery of the chair.
- Adjustable wrench. This tool will come in handy if the screws on your office chair base are stubborn and refuse to budge. Also, make sure that the wrench is the right size so that you don’t strip the screws.
- Putty knife. This tool will be used to pry off the plastic plugs that cover the screws on your office chair base.
- WD-40 or another lubricant. This will be used to help loosen any stubborn screws on your office chair base.
- Pencil. This is optional, but it’s always a good idea to have a pencil handy in case you need to make any adjustments along the way.
Steps To Remove Office Chair Base
Photo Source: mydecorative.com
Now that you have gathered all of the necessary tools, it’s time to get started!
- Unscrew The Base Of Office Chair
The first thing that you need to do is locate the screws that hold your office chair base in place. In most cases, there will be four screws—one in each corner. Once you have located the screws, use your Phillips head screwdriver to remove them. In some cases, the screws may be stubborn and refuse to budge. If this is the case, use your adjustable wrench to loosen them.
- Remove The Plastic Plugs
Once the screws have been removed, it’s time to remove the plastic plugs that cover them. To do this, insert the putty knife under the edge of the plug and pry it off. In some cases, the plugs may be stubborn and refuse to budge. If this is the case, use your hammer to tap on the putty knife, which will help loosen the plug.
- Remove The Base
Now that the screws and plugs have been removed, you should be able to simply lift the base off of the chair. In some cases, the base may be stuck due to dried-on dirt and grime. If this is the case, use a generous amount of WD-40 or other lubricant to help loosen it.
- Clean The Chair
Now that the base has been removed, take this opportunity to clean your office chair. Use a damp cloth to wipe down the entire chair, paying special attention to any areas where the base was attached. This will help remove any dirt and grime that has built up over time.
Take note that once the chair has been cleaned, it’s time to reattach the base. Simply reverse the steps that you took to remove it and you should be all set! Following these steps should help make the process of removing your office chair base a breeze.
Additional Tips In Removing Office Chair Base
Photo Source: tincci.com
Here are some additional tips to help you remove your office chair base:
- Make sure that the area around the screws is clean before attempting to remove them. This will make it easier for the screwdriver to grip the screws and prevent them from stripping.
- Be careful not to damage the plastic plugs when removing them. If they are damaged, they may not fit back into place properly when you reattach the base.
- If the screws are stubborn and refuse to budge, try applying a little bit of WD-40 or another lubricant to them. This will help loosen them and make them easier to remove.
- Be careful not to over-tighten the screws when reattaching the base. This can strip the threads and make it difficult to remove the base in the future.
- If the plastic plugs are stubborn and refuse to budge, try heating them up with a hairdryer or heat gun. This will help soften the plastic and make it easier to remove.
With these tips, you should be able to easily remove your office chair base without any problems!
Now that you know how to remove your office chair base, you can easily take care of any maintenance or repairs that need to be done. Be sure to follow the steps carefully and take your time so that you don’t damage any of the parts. With a little bit of patience, you should be able to remove the base and reattach it without any problems.
My name is James McGee and I am an experienced blogger and content creator. I run chairsteam.com, a website dedicated to providing readers with informative and entertaining insights into the world of chairs. Through this blog, I hope to share my passion for furniture design with people from all walks of life. My mission is to make sure that everyone can find the perfect chair they need. Let’s explore chairs together!